Stealthburner Toolhead PCB

Afterburner Toolhead PCB 4.0 Kit ERCF Edition with all required connectors, sockets and crimp contacts. Including 5 spare crimps per type each. SMD components are now pre-soldered. You need to solder all through-hole components.Designed by hartk, Documentation can be found at GitHub

This screw kit contains all screws, nuts and heat stakes needed to build a Stealthburner according to the manual. You continue to use your existing Clockwork or Galileo extruder. Also included are the inserts and screws for the recently added ADXL mount. Important: Because Stealthburner has no BOM yet, we include at least one spare screw or nut. You will have leftovers! The picture doesn't show the current kit contents, we'll update the picture soon! Contents:M3x50 SHCS3M3x25 SHCS5M3x16 SHCS3M3x12 SHCS5M3x6 FHCS3M3 Brass heat stakes - M3x5x4  6Self-tapping Screw 2x103

The Rainbow Barf Diffusor for use with the Stealthburner, printed in transparent PETG (which is the only exception when you should use PETG in your Voron ever!). We include 2 pieces because print defects are pretty hard to spot.Note that this part was printed on request (latest version as of 5th September 2022), and we made a few more. We did not test the part, so buy it on your own risk as we don't follow any updates to the printed part.

Orion OD4010-24HB, suitable as StealthBurner Hotend FanEvery fan is tested individually on arrival and padded with some bubble wrap for additional protection during shipping.Technical data:Operational Voltage (nominal)24VRotational Speed8000 RPMAir Flow0.263 m³/min (9.3cfm, 15.8m³/h)Static Pressure0.20 in H2ONoise Level33.4dBCurrent60mA

3 pieces SK6812 neutral white for use in the Stealthburner, including a 100 Ohm resistor to avoid signal reflections (see below). The SK6812 has red, green and blue LEDs as well as a dedicated white LED to achieve a pure white color without a blue tint. Please check the comparison pictures. The color_order for Klipper needs to be GRBW. Connect them to your Neopixel/RGB-Port of your printer mainboard - make sure you have a current mainboard like Fysetc Spider or SKR 1.4/Octopus/Octopus Pro by Bigtreetech. If you already used the Neopixel/RGB-Port of your printer mainboard - no problem! You can connect DOUT of your existing strip to DIN of these LEDs. You just have to ensure that you have the same LED type - if your existing strip has RGB Neopixels, use WS2812B. If your existing strip has RGBW Neopixels, use SK6812. Important! The data signal can be degraded if you run it over a long wire (signal reflections on transmission lines). If your LEDs don't show the desired colors or switch colors at random please try a very short cable to the mainboard first to ensure your wiring is correct. Then put the 100-120 Ohm resistor in-line with your DIN wire as close to the mainboard: DIN Mainboard -> 100-120 Ohm resistor -> long wire -> Neopixel DIN.    

Z Endstop Kit consisting of:Z Endstop PCB1Omron D2F1XH Plug1XH Socket1Crimp Contacts3M2x10 Screws5Tools required for assembly:Soldering Iron, SolderCompatible XH CrimperDesigned by hartk, Documentation can be found at GitHub

The transparent printed part [c]_stealthburner_LED_diffuser.stl for the Stealthburner, printed in transparent PETG (which is the only exception when you should use PETG in your Voron ever!). We include 2 pieces because print defects are pretty hard to spot.

Operational Voltage 24V Rated Current 80mA Rated Speed 10000 RPM +-10% Air Flow 11.0cfm (18.6m³/h, 0.3m³/min) Static Pressure 0.29 In H2O (7.3 mmH2O) Acoustic Noise 36.8 dB(A)

XY Microswitch Endstop Kit with the following contents:XY Endstop PCB1M3x8 SHCS2 KW10 Microswitch2XH Plug1XH Socket1XH Crimp Contacts6Tools required for assembly:Soldering Iron, SolderCompatible crimperDesigned by randellhodges, documentation can be found at GitHub