A4T Toolhead

Replimat Labs

A4T Hardware Kit

Hardware Kit for the A4T. Comes with the SK6812 RGBW LEDs, 26AWG FEP wires (3x1m) and mounting hardware for all extruder variantsYou might wish to complement this kit with small zip-ties.Qty Part 5 M3 Square Nut 4 M3x08 SHCS, V2A 3 M3x06 BHCS, V2A 2 M3x50 SHCS, V2A 3 M3x16 SHCS, V2A 3 M3x20 SHCS, V2A 3 M3x12 SHCS, V2A 3 SK6812 LED PCB 3 26AWG Wires, 1m each 3 Heatset Insert M3x5x4 2 M3x20 Standoff 2 M3x30 Pin 2 M4 Metal Tube, 22.5mm

€14.50*

Replimat Labs

XoL Carriage Tube & Pin

Set of:2x tubes (4mm OD, ~3.2mm ID, 22mm length2x Pin d=3mm, length = 30mmSuitable for the XoL carriage

€2.50*

Crossbow Filament Cutter

Designed by DW Tas, Manufactured by Fysetc. Crossbow was designed and developed around the A4T, but is intended for universal for use in printed toolheads that have a flat mounting surface below the extruder. Crossbow A4T parts can be downloaded here: https://github.com/Armchair-Heavy-Industries/A4T. Package contents:1x Crossbow Filament Cutter3x Square M3 Nut3x Heatset Insert3x M3x16 BHCS Screw2x Spare Blades1x Rubber Installation Helper1x Spare Set Screw2x Hex Key

€25.00*

25x25x10mm

XoL / A4T

24V

Gdstime

Gdstime GDA2510 / Gdt2510S12B, Dual Ball Bearing, 24V

Gdstime 2510 Axial Fan, suitable for Xol. Model Number Gdt2510S12B / GDA2510.Dual Ball Bearing, 24V, 60mA, 12000 RPM, 2.45 cfm, 27.46dB(a), 0.24 InH2O

€8.90*

40x40x10mm

XoL / A4T

24V

Gdstime

Gdstime GDB4010, Dual Ball Bearing, 24V

Gdstime 4010 Blower Fan, suitable for Xol and DragonBurner. Model Number GDB4010. Dual Ball Bearing, 24V, 100mA, 12000 RPM, 4.17 cfm, 37dB(a), 0.72 InH2O

€7.50*

25x25x10mm

XoL / A4T

Delta Electronics

Delta ASB02505SHA-AY6B

The Delta ASB02505SHA-AY6B comes with wiring instructions and the diode to prevent the fan spinning when it's supposed to be off.Relevant config options for Klipper tachometer_pin: # Set to the pin you like to use. Make sure it has either a hardware or software pullup tachometer_ppr: 2 tachometer_poll_interval: 0.0009 Technical data Operational Voltage 5V Rated Current 120mA Rated Speed 15000 RPM +-15% Air Flow 4.31cfm (7.32m³/h, 0.122m³/min) Static Pressure 0.32 inH2O (8.13 mmH2O) Acoustic Noise 31 dB(A) 1N4148 diode is included.

€9.90*

3 pcs SK6812 RGBW for Stealthburner / A4T

3 pieces SK6812 neutral white for use in the Stealthburner, including a 100 Ohm resistor to avoid signal reflections (see below). The SK6812 has red, green and blue LEDs as well as a dedicated white LED to achieve a pure white color without a blue tint. Please check the comparison pictures. The color_order for Klipper needs to be GRBW. Connect them to your Neopixel/RGB-Port of your printer mainboard - make sure you have a current mainboard like Fysetc Spider or SKR 1.4/Octopus/Octopus Pro by Bigtreetech. If you already used the Neopixel/RGB-Port of your printer mainboard - no problem! You can connect DOUT of your existing strip to DIN of these LEDs. You just have to ensure that you have the same LED type - if your existing strip has RGB Neopixels, use WS2812B. If your existing strip has RGBW Neopixels, use SK6812. Important! The data signal can be degraded if you run it over a long wire (signal reflections on transmission lines). If your LEDs don't show the desired colors or switch colors at random please try a very short cable to the mainboard first to ensure your wiring is correct. Then put the 100-120 Ohm resistor in-line with your DIN wire as close to the mainboard: DIN Mainboard -> 100-120 Ohm resistor -> long wire -> Neopixel DIN.

€1.70*