Voron Trident

Hardware Kit (Screws, Washers, Heatset Inserts and optionally extrusion nuts) for building a Voron Trident R2. The required quantities were determined using the Voron configurator with the following settings: Direct Feed New Build Blind Joints 300mm Spec Not included by default are the F695-2RS bearings, giving you the choice if different ABEC classes should you so desire. Also not included is the MR85ZZ bearing, as this is usually included with extruder hardware.Bill of Materials Qty Part BOM count Extras 120 Heatset Insert M3x5x4 109 11 17 Heatset Insert M5x7x6 15 2 7 M3 Lock Nut 6 1 5 M3 Washer 4 1 65 M3x06 BHCS, V2A 59 6 19 M3x06 FHCS, V2A 17 2 158 M3x08 SHCS, V2A 143 15 3 M3x10 FHCS, V2A 2 1 81 M3x12 SHCS, V2A 73 8 30 M3x16 SHCS, V2A 27 3 4 M3x20 SHCS, V2A 3 1 11 M3x25 SHCS, V2A 10 1 15 M3x30 SHCS, V2A 13 2 10 M3x40 SHCS, V2A 9 1 3 M3x50 SHCS, V2A 2 1 3 M4 Knurled Nut 3 0 8 M4x6 BHCS, V2A 7 1 50 M5x10 BHCS, V2A 45 5 64 M5x16 BHCS, V2A 58 6 5 M5x30 BHCS, V2A 4 1 5 M5x40 BHCS, V2A 4 1 19 Screw 2x10mm 17 2 27 Shim Rings 5x10x1 24 3 Roll-in/Hammerhead Nuts BOM Qty Part BOM count Extras 98 Roll-in Nut M3 89 9 76 Roll-in Nut M5 69 7 61 Hammerhead M3 Nut 55 6 Roll-in nut compatibility Note that we cannot guaranteee proper fitment of the Roll-in nuts - every extrusion manufacturer makes their extrusions a bit different. European 2020 profiles Type B with 6mm wide slot typically work, as well as those delivered by Formbot. I personally tested those on a Voron 1.8 LDO Extrusion Kit, but I don't know if LDO changed the style of their extrusions.

Hardware Kit for upgrading your Voron Trident to the latest R2 release. The required quantities were determined using the Voron configurator with the following settings: Direct Feed I have a Voron Trident R1 already Blind Joints 300mm Spec Since you will reprint many parts, we set the number of M3 heatset inserts to what you would need for a full rebuild, so that you don't need to remove the heatset inserts from your old parts. You will need the quantities from your old R1 build. If you bought a kit (Formbot/LDO/Siboor etc), you need to compare their screw quantities against the Trident R1 BOM to ensure you have enough screws. If you want to be on the safe side, we offer a worry-free full screw kit for the Trident R2 build. Full Hardware Kit You also need at least 4 F695 Bearings - select the desired quantity when adding the product to the basket. Kit Contents Qty Part Upgrade BOM Extras 120 Heatset Insert M3x5x4 109 * 11 17 Heatset Insert M5x7x6 15 2 9 M3 Roll-in nut 8 1 2 M3 Washer 1 1 31 M3x06 BHCS, V2A 28 3 11 M3x12 SHCS, V2A 10 1 13 M3x16 SHCS, V2A 11 2 5 M3x25 SHCS, V2A 4 1 7 M3x40 SHCS, V2A 6 1 18 M5x16 BHCS, V2A 16 2 5 M5x40 BHCS, V2A 4 1 3 Shim Rings 5x10x1 2 1 * Same amount as full kit, based on the assumption that you might want to re-print all parts and don't want to extract your old heatset inserts Roll-in nut compatibility Note that we cannot guaranteee proper fitment of the M3 Roll-in nuts - every extrusion manufacturer makes their extrusions a bit different. European 2020 profiles Type B with 6mm wide slot typically work, as well as those delivered by Formbot. I personally tested those on a Voron 1.8 LDO Extrusion Kit, but I don't know if LDO changed the style of their extrusions.